Trailer Wiring Diagram
What each wire does on 4, 5, 6 and 7 pin trailer plugs. Pick your connector and wire color below. Where manufacturers disagree, you get every answer, because trailer wire colors are not a true standard.
Test it before you trust the color. Hopkins says to identify wires "by function only" because color coding is not standard among manufacturers, and etrailer says to match pins by function with a circuit tester, because crossed wiring can damage electrical components. A wrong guess here means crossed turn signals or trailer brakes that do not work.
Wire colors by connector
4-way flat
Lights only: the usual plug on utility trailers and boat trailers without surge brakes.
| Wire | Function |
|---|---|
| White | Ground |
| Brown | Tail lights |
| Yellow | Left turn and brake |
| Green | Right turn and brake |
From: CURT, Lippert, Croft, Hopkins
5-way flat
4-way plus one wire, usually for trailers with surge brakes.
| Wire | Extra wire blue | Extra wire purple |
|---|---|---|
| White | Ground | Ground |
| Brown | Tail lights | Tail lights |
| Yellow | Left turn and brake | Left turn and brake |
| Green | Right turn and brake | Right turn and brake |
| Blue | Reverse lights or surge brake lockout | - |
| Purple | - | Reverse lights |
The extra wire feeds off the vehicle's backup lights. It may run reverse lights, or the reverse lockout that stops surge brakes applying when you back up.
From: CURT, etrailer, Croft, Hopkins
6-way round
Adds electric brakes and 12V power. Common on goosenecks.
| Wire | 12V on black | 12V on red |
|---|---|---|
| White | Ground | Ground |
| Brown | Tail lights | Tail lights |
| Yellow | Left turn and brake | Left turn and brake |
| Green | Right turn and brake | Right turn and brake |
| Red | - | 12V power or auxiliary |
| Blue | Electric brakes | Electric brakes |
| Black | 12V power | - |
Hopkins says brake and 12V power have two different industry standards on this plug, and etrailer says they are reversed in some applications. Find out which your trailer uses before you connect it.
From: CURT, Croft, Hopkins
7-way round pin
Not the same plug as the RV blade. etrailer calls the round-pin style very rare.
| Wire | Function |
|---|---|
| White | Ground |
| Brown | Tail lights |
| Yellow | Left turn and brake |
| Green | Right turn and brake |
| Red | Auxiliary power |
| Blue | Electric brakes |
| Black | Reverse lights |
From: CURT
7-way RV blade
Flat blades in a round housing. The usual plug on travel trailers and fifth wheels, and on newer trucks and SUVs with a factory hitch.
| Wire | Traditional RV | SAE J2863 (per CURT) | Hopkins sheet | Croft hardwired |
|---|---|---|---|---|
| White | Ground | Ground | Ground | Ground |
| Brown | Right turn and brake | Tail lights | Tail lights | Tail lights |
| Yellow | Reverse lights or auxiliary | Left turn and brake | Left turn and brake | Left turn and brake |
| Green | Tail lights | Right turn and brake | Right turn and brake | Right turn and brake |
| Red | Left turn and brake | - | 12V power | Center auxiliary |
| Blue | Electric brakes | Electric brakes | Electric brakes | Electric brakes |
| Black | 12V power | - | - | 12V power |
| Orange | - | 12V power | - | - |
| Grey | - | Reverse lights (CURT) or brake lights only (Lippert) | - | - |
| Purple | - | - | Reverse lights | - |
On a narrow screen this table scrolls sideways to show all 4 schemes.
Only white and blue mean the same thing in every scheme below. Brown, green, yellow and red all change.
From: CURT, Lippert, Croft, Cal OES, Hopkins
A conflict we could not settle. On the SAE 7-way, CURT lists grey as reverse lights and Lippert lists it as brake lights only. The SAE standard is a paid document, and its published summary covers the connector rather than wire colors. So we show both. To check yours, set the parking brake, turn the ignition on, and test that wire: if it goes live in reverse it is reverse lights, and if it goes live when you press the brake pedal it is brake lights.
Which 7-way RV blade scheme do I have?
Do not go by color alone. Identify each wire by the job it does, using the pin diagram below and a circuit tester. As a starting point, CURT says the traditional scheme is typical on fifth wheels, travel trailers and campers, and SAE on goosenecks, utility, cargo and equipment trailers.
The quickest clue is the tail light wire. Turn on the running lights and test: if green goes live, you are probably looking at traditional; if brown does, one of the others.
Pin diagrams
A plug and a socket are mirror images. Left and right swap depending on which one you are looking at, and on whether you are looking at the contacts or at the back where the wires attach. These all show the contact side, looking straight at the pins. The screw terminals on the back of a hardwired connector are reversed left to right from these.
7-way RV blade, keyway notch at the bottom
6-way round, tail light pin at the top
*Hopkins says brake and 12V have two industry standards on this plug, and etrailer says they are reversed in some applications. Test before you connect.
From: Hopkins, Croft, Cal OES. Pin numbers are left off on purpose: the numbers printed on connectors and in guides vary, and the position is what you can check with your own eyes.
4-way and 5-way flat
The wires run in a line: white, brown, yellow, green, and on a 5-way, the extra wire last. The trailer side is the male half and the vehicle side is the female half.
From: Croft
Which connector does my trailer use?
| Trailer | Common | Also used |
|---|---|---|
| Utility trailer | 4-way flat | 6-way round, 7-way RV blade |
| Boat trailer, no surge brakes | 4-way flat | 7-way RV blade (rarely used) |
| Boat trailer with surge brakes | 5-way flat | 6-way round, 7-way RV blade |
| Pop-up camper | 6-way square | 6-way round |
| Travel trailer | 7-way RV blade | 6-way round, 7-way round |
| Fifth wheel | 7-way RV blade | 6-way round |
| Gooseneck | 6-way round | 7-way RV blade |
From: CURT. Typical, not universal. Check your own plug.
Suggested minimum wire gauge
| Wire | 4 and 5 way | 6 and 7 way |
|---|---|---|
| Turn, brake light, tail and reverse | 18 | 16 |
| Ground | 16 | 12 |
| Electric brakes | - | 12 |
| 12V battery feed (must be fused) | - | 12 |
From: Hopkins, its suggested minimums. A lower gauge number is a thicker wire.
If power reaches the trailer, check the ground first
etrailer says that when the signal is reaching the trailer, the most likely problem is a ground wire that is not secured properly. The trailer's wiring grounds to the frame near the coupler, and each light needs a ground too, through its own white wire or its mounting studs. Too much paint, dirt or rust makes a bad ground, so make sure it meets bare metal. Also look for pinched or cut wires, which etrailer says are often found where wires run above the suspension or behind the tail lights.
If your trailer has electric brakes, the next step after wiring is setting the gain. See how to set a trailer brake controller.
Common questions
What is the standard trailer wiring color code?
On a 4-way flat plug the colors are consistent across CURT, Lippert, Croft and Hopkins: white is ground, brown is tail lights, yellow is left turn and brake, and green is right turn and brake.
Past 4 and 5 way there is no single code. Hopkins says plainly that color coding is not standard among all manufacturers and to identify wires by function only. On a 7-way RV blade the same color can mean different things, so read the tables above and test before you rely on a color.
What is the difference between the two 7-way RV blade color schemes?
CURT publishes two. In the traditional scheme green is tail lights, red is left turn, brown is right turn, black is 12V and yellow is reverse. In the SAE J2863 scheme as CURT lists it, brown is tail lights, yellow is left turn, green is right turn, orange is 12V and grey is reverse. CURT says traditional is typical on fifth wheels, travel trailers and campers, and SAE on goosenecks, utility, cargo and equipment trailers.
The pins do the same job either way. Only the wire colors behind them change, which is why a color chart alone can leave you with crossed turn signals.
What does the grey wire do on a 7-way trailer plug?
The sources disagree. CURT lists grey as reverse lights on the SAE configuration. Lippert's guide lists it as brake lights only.
We could not settle it from what is publicly available, so check yours with a circuit tester. With the parking brake set and the ignition on, see whether that wire goes live in reverse or when you press the brake pedal.
Which wire is the trailer brake wire?
Blue on 6-way and 7-way plugs, in every source we checked. On the 7-way RV blade it is the bottom blade beside ground, so the position is a second check on the color.
On a 5-way flat plug, blue does not run electric brakes. There it feeds reverse lights or a surge brake lockout. And on a 6-way round plug, Hopkins and etrailer both warn that the brake and 12V pins are reversed in some applications.
What color is the ground wire, and where does it go?
White, on every connector in every source here. CURT says it should be properly grounded at the trailer tongue, and etrailer says the system is grounded to the frame near the coupler.
Hopkins calls for a ground point that is metal, uncoated and rustproof, and etrailer warns that too much paint, dirt or rust causes bad grounds, so secure it to bare metal. Each light needs a ground too, either its own white wire or through its mounting studs.
What is the difference between 4, 5, 6 and 7 way?
Each step adds functions. 4-way carries tail, left and right lights plus ground. 5-way adds one wire, for reverse lights or a surge brake lockout. 6-way adds electric brakes and 12V power instead. 7-way carries all of them: lights, ground, brakes, 12V and reverse or auxiliary.
Choose by what the trailer has. A trailer with electric brakes needs a 6-way or 7-way connector.
What size wire do I need for trailer lights and brakes?
Hopkins suggests a minimum of 18 gauge for lights and 16 for ground on 4-way and 5-way setups. On 6-way and 7-way it suggests 16 for lights and 12 for ground, brakes and the battery feed. A lower gauge number is a thicker wire.
Those are its suggested minimums, not a rule for every trailer. Hopkins also specifies a fuse block or fused battery lead for the 12V feed.
Does this cover 30 amp or 50 amp RV plugs?
No. Those are shore power plugs carrying mains voltage, which is a different system and a different safety problem. This page covers only the low-voltage connector between the tow vehicle and the trailer.
Related tools
- Hitch Class SelectorWhich receiver class covers your trailer weight and tongue weight.
- Trailer Axle Weight ChartCommon axle capacities, what a bare axle weighs, and how to identify the axle you have.
- Trailer Tire Load Range ChartLoad range B to F, ply equivalence and max pressure — plus what load range your trailer actually needs.
Sources
- CURT - Trailer Wiring Diagram and Installation Help - wire colors for every connector, both 7-way RV blade configurations, and common connectors by trailer type
- Lippert - Ultimate Trailer Wiring Guide - wire colors by function; disagrees with CURT on the SAE grey wire
- Hopkins - Model 48245 trailer wiring instructions (PDF, retailer-hosted copy) - pin positions on both connector faces, suggested minimum wire gauge, and the warning that color coding is not standard
- Croft Trailer Supply - 6 & 7-Way Connector Wiring Diagrams (PDF) - each connector drawn from the front face and from the wire side; flat connector order
- California Governor's Office of Emergency Services - 7-Way Trailer Wiring Diagram (PDF) - numbered 7-pole RV connector, vehicle end and trailer end
- etrailer - Trailer Wiring Diagrams - testing by function, the 5-way reverse lockout, the swapped 6-way pins, and grounding
- SAE J2863 - Automotive Trailer Tow Connector - the standard itself is paid and was not read for this page; the color table labelled SAE here is as CURT publishes it